BLOG
VR

Screw Compressor Overheating: 7 Real Causes (And the One Nobody Tells You) | ZIQI

Screw Compressor Overheating: 7 Real Causes (And the One Nobody Tells You) | ZIQI
Marin Hu - Full-Domain Marketing Expert & Compressed Air Systems Engineer at ZIQI
Marin Hu            

Full-Domain Marketing Expert & Compressed Air Systems Engineer

ZIQI Compressor Group · Updated May 2026

ZIQI · Est. 2007            200 Export Markets            Field Engineer            Google Ads & SEO

By Marin Hu — Compressed Air Systems Engineer · Updated May 6, 2026 · 12 min read

A screw compressor overheating and shutting down on high-temperature alarm is one of the most common — and most misdiagnosed — failures in industrial compressed air systems. The standard checklist covers oil level, cooler condition, and ventilation. Most maintenance guides stop there. They miss the cause behind 60% of chronic summer overheating cases: a motor wound with copper-clad aluminum wire that runs 15–25°C hotter than spec at full load, silently pushing discharge temperatures over the protection threshold every time the weather gets warm.

This guide covers all seven root causes in diagnostic order — starting with the quick checks and ending with the one that requires a material certificate to confirm.

01 — REFERENCE Normal Operating Temperature Range

Before diagnosing a fault, establish what normal looks like. For an oil-injected rotary screw compressor at 7–10 bar working pressure:

75–95°C
Normal Operating Range
95–100°C
Watch Zone — Investigate
100–105°C
Pre-Alarm — Act Now
>105°C
Protection Shutdown
Temperature PointNormal ValueAction Required
Thermal bypass valve opens~70°CNormal — oil begins routing through cooler
Thermal bypass fully open82–85°CNormal — full cooling flow active
Normal discharge temperature75–95°CNormal operating range
Elevated — investigate95–100°CCheck oil, cooler, ventilation
High-temp alarm threshold105–110°CCompressor shuts down — fault diagnosis required
Below normal (too cold)<70°CBypass valve may be stuck closed — check for oil emulsification
Note on ambient temperature: Every 10°C rise in compressor room ambient temperature increases discharge temperature by approximately 8–12°C. A machine running at 88°C in January may hit 100°C in August with no other change. This is normal physics — but it is also the environment in which hidden motor faults become visible.

02 — ROOT CAUSES All 7 Causes of Screw Compressor Overheating

Ranked by diagnostic frequency — start from the top, work down. Each cause has a field-test method and a fix.

01
Most Common — Check First
Degraded or Low Lubricating Oil

Lubricating oil absorbs 80–90% of the heat of compression. When oil degrades past its service life, its viscosity drops and oxidation byproducts accumulate — thermal capacity falls significantly even at correct fill level. Low oil volume reduces the total heat sink available per compression cycle.

Field test: Check oil level in the sight glass at operating temperature. Draw a sample — oil should be amber to light brown. Dark brown, black, milky (water contamination), or foam indicates degradation requiring immediate change.

Oil degraded past service interval, or extended drain intervals under heavy load or high ambient conditions.
Change oil immediately. For machines running in ambient above 35°C, reduce oil change interval by 25%. Use only the grade specified for your ambient temperature range.
02
Common — Visual Check
Clogged Oil Cooler or Aftercooler

Cooler fins accumulate dust, oil mist, and debris over time. A cooler operating at 30% blockage rejects significantly less heat, causing discharge temperatures to rise. This is the most visually obvious fault and the most frequently blamed — but it is often not the only cause, especially when overheating is seasonal.

Field test: Inspect cooler fins visually. Run a flashlight through the fin stack — you should see light through. Feel the cooler outlet air temperature with your hand. If the cooler fan is running but the outlet air is not noticeably warm, heat rejection is compromised.

Inadequate maintenance schedule for compressor room cleanliness. High-dust environments require more frequent cooler cleaning.
Clean cooler fins with compressed air (blow from clean side to dirty side) or low-pressure water wash. Do not use high-pressure water directly on fins — it bends them and reduces airflow. Establish a quarterly cleaning schedule in dusty environments.
03
Common — Component Test Required
Failed Thermal Bypass Valve (Stuck Open)

The thermal bypass valve controls oil temperature by mixing cooled and uncooled oil flows. When the wax-element thermostat inside the valve fails in the open position, hot oil bypasses the cooler entirely and returns directly to the airend — causing discharge temperatures to climb rapidly from startup.

Signature pattern: Temperature rises steadily to alarm within 10–20 minutes of startup. Cooler is clean. Oil is fresh. The machine trips reliably and quickly, regardless of ambient temperature.

Field test: Compare oil temperature at cooler inlet versus cooler outlet at operating temperature. If temperatures are nearly identical, oil is not flowing through the cooler — the bypass valve is failing open.

Wax thermostat element mechanical failure. Typical service life: 20,000–40,000 hours. Accelerated by contaminated oil or temperature cycling above rated range.
Replace thermal bypass valve assembly. This is a low-cost part ($40–$120 depending on model) but requires draining the oil circuit. Confirm replacement part matches the valve's opening temperature specification for your model.
04
Environmental — Room Assessment
Inadequate Compressor Room Ventilation

Compressor rooms must supply enough cool inlet air to support cooling and exhaust the heat load generated by the motor and compression process. A 75 kW compressor generates approximately 70 kW of heat that must be removed from the room. Undersized ventilation causes inlet air temperature to rise progressively during operation, compounding discharge temperatures.

Field test: Measure compressor room air temperature at the compressor inlet with a thermometer. Temperature above 40°C at the inlet in a 30°C ambient environment indicates ventilation is inadequate. The room is accumulating its own heat.

Compressor installed in an enclosed room without calculated ventilation design. Or ventilation was adequate when installed but production expansion increased thermal load.
Ensure compressor room has dedicated inlet (cool air in) and exhaust (hot air out) paths. Inlet area should be at least 0.5m² per 100 kW of installed compressor power. For duct-connected cooler exhaust, duct pressure drop must be within the fan's rated capacity.
05
Mechanical — Fan Inspection
Cooling Fan Fault or Wrong Rotation Direction

The cooling fan draws ambient air across the cooler fins to reject heat. A failed bearing, a broken blade, or — in the case of recently replaced three-phase motors — reversed rotation direction will dramatically reduce airflow and heat rejection.

Field test: With the machine running, verify air movement across the cooler. Hold a strip of paper near the cooler — it should be drawn toward the cooler (suction fan) or blown away (pressure fan), depending on your model's design. Reversed rotation is surprisingly common after motor rewinding or replacement.

Fan motor bearing failure. Broken or cracked fan blade. Incorrect phase wiring after motor service causing reverse rotation.
Confirm fan rotation direction against the arrow label on the housing. For three-phase fans, swap any two power leads to reverse rotation if incorrect. Replace fan assembly if bearing noise or blade damage is present.
06
Oil Circuit — Internal Contamination
Rust Sludge Blocking Oil Passages

Rust sludge partially blocks oil passages, thermostat ports, and cooler internal channels — reducing oil flow rate and heat transfer efficiency simultaneously. This cause is insidious because it develops gradually over years.

Carbon steel internal piping corroding under normal condensate exposure. Rust accumulation begins within 2–3 years of operation.
Flush the oil circuit with flushing oil to remove accumulated sludge. Inspect and clean the thermostatic valve seat for rust deposits. For long-term prevention: machines with 304 stainless steel internal piping (such as the ZIQI standard) do not develop this fault — no ferrous material in the oil circuit means no rust contamination regardless of condensate accumulation.

03 — THE EVIDENCE Why the CCA Problem Is Systematic, Not Accidental

Copper-clad aluminum in compressor motors is not a manufacturing defect. It is a deliberate specification decision made to reduce bill-of-materials cost at the factory stage. The cost saving per motor is modest — perhaps $80–$180 on a 75 kW unit. The downstream cost to the end user is orders of magnitude higher.

MetricCCA-Wound MotorPure Copper IE4 Motor
Motor cost premium at factoryBaseline+$80–$180
Operating temperature at full load15–25°C above ratingWithin rated spec
Summer shutdown frequencyCommon in hot climatesEssentially zero
Motor rewind cost (failure)$1,200–$3,500N/A — does not fail thermally
Downtime per summer incident4–12 hoursZero
Identifiable before purchaseOnly with material certificateCertificate available on request
10-year cost difference$18,000–$45,000 in downtime, repairs, and energy waste
The question that ends the ambiguity: Ask your current compressor supplier for the motor winding material test certificate — a third-party document from the motor manufacturer confirming copper content of the winding wire. A supplier with pure copper motors provides this document in minutes. A supplier with CCA motors typically says it is "not available" or "not standard practice." The response tells you everything.

At ZIQI, every compressor ships with the motor material certificate from WEG (Brazil) or Wolong, confirming 100% copper windings and IE4/IE5 efficiency class. This is not a premium option. It is the standard specification, because a machine that trips on high temperature in July is not a machine — it is a liability.

04 — PROCEDURE Step-by-Step Diagnostic Sequence

Use this sequence for any screw compressor that is shutting down on high-temperature alarm. Work top to bottom — each step rules out one cause before moving to the next.

High-Temperature Shutdown Diagnostic — Field Procedure
01
Check oil level and condition. Level in sight glass at operating temperature. Sample color and smell. If dark, burnt, or milky → change oil before proceeding. New oil baseline required for accurate further diagnosis.
02
Inspect cooler fins. Visual inspection of oil cooler and aftercooler. Run flashlight through fin stack. Clean if blockage visible. Record cooler inlet/outlet temperatures with infrared thermometer after cleaning.
03
Test thermal bypass valve. Compare oil temperature before and after cooler at operating temp. Difference of less than 5°C indicates valve is not routing oil through cooler. Replace valve if confirmed.
04
Measure compressor room inlet air temperature. At compressor air filter inlet. If above 40°C in a 25–30°C ambient environment — ventilation is inadequate. Improve before further diagnosis.
05
Verify cooling fan operation. Confirm rotation direction (match arrow on housing). Check for blade damage or bearing noise. Verify motor current matches nameplate at running speed.
06
Flush oil circuit for rust contamination. If machine is over 3 years old with carbon steel piping and overheating has developed gradually — flush with approved flushing oil. Inspect thermostat ports for rust deposits.
07
Request motor winding material certificate. If all above pass and overheating is seasonal (summer only, correlates with ambient temperature) — the motor is the remaining suspect. Request certificate from your supplier. If unavailable → consider motor winding analysis or replacement with certified copper-wound unit.
Time to resolution by cause: Oil change → 2 hours. Cooler clean → 1 hour. Bypass valve → 4 hours. Ventilation → 1–3 days. Fan → 2 hours. Oil flush → 4 hours. CCA motor → motor replacement or rewind, 1–5 days. Identifying the correct cause first saves you from unnecessary repairs.

05 — PREVENTION Long-Term Prevention: The Specification Approach

Reactive maintenance fixes the symptom. The causes of chronic overheating are built into the machine at the specification stage — and the only way to prevent them permanently is to specify correctly before purchase.

Root CauseReactive FixPermanent Prevention at Spec Stage
Oil degradationMore frequent changesSpecify synthetic oil compatibility and extended-life oil circuit design
Cooler blockageQuarterly cleaningSpecify cooler with accessible fin design for your environment
Bypass valve failureReplace every 20–40k hrsStandard maintenance item — no specification change prevents it
Poor ventilationRoom modificationCalculate ventilation requirement before installation, not after
Rust sludge in oilPeriodic flushSpecify 304 stainless steel internal piping — no ferrous material, no rust
CCA motor windingsMotor rewind or replacementSpecify IE4/IE5 motors from WEG or Wolong with material certificate — no CCA risk

The two causes that cannot be fixed without replacing components — rust contamination and CCA motor windings — are both consequences of specification decisions made at the factory before the machine was assembled. They are not wear items. They are design choices. And the only way to avoid paying for them over the machine's life is to require documentation before purchase.

Related Failure Diagnostic Guides

Related Failure Diagnostic Guides

FAQ Frequently Asked Questions

Why does my screw compressor keep overheating and shutting down?
The most common causes are degraded oil, a clogged cooler, a stuck thermal bypass valve, inadequate room ventilation, and a faulty cooling fan. The most overlooked cause — responsible for the majority of chronic summer shutdowns — is a motor wound with copper-clad aluminum wire instead of pure copper. CCA motors run 15 to 25 degrees Celsius hotter at full load, pushing discharge temperatures over the protection threshold on hot days even when all cooling hardware is functioning correctly.
What temperature is too hot for a screw air compressor?
Normal operating range for an oil-injected screw compressor is 75 to 95 degrees Celsius at 7 to 10 bar. High-temperature protection typically triggers a shutdown at 105 to 110 degrees Celsius. Temperatures consistently above 95 degrees Celsius under normal ambient conditions indicate an underlying fault. Temperatures below 70 degrees Celsius suggest the thermal bypass valve may be stuck closed, causing water condensation in the oil.
How do I fix a screw compressor that keeps overheating?
Follow this sequence: check oil level and condition first, then inspect and clean cooler fins, test the thermal bypass valve, measure inlet air temperature in the compressor room, verify cooling fan rotation and condition, flush the oil circuit if the machine is over 3 years old with carbon steel piping, and finally — if overheating is seasonal and all else passes — request a motor winding material certificate to rule out copper-clad aluminum windings.
What causes a screw compressor to overheat in summer but not winter?
Seasonal overheating that disappears in winter and returns in summer is the signature of a latent motor winding fault. Motors wound with copper-clad aluminum wire run 15 to 25 degrees Celsius hotter than copper-wound motors at identical load. In winter, this excess heat stays within safe limits. When summer ambient temperatures add another 10 to 15 degrees of thermal load to the system, the CCA motor pushes discharge temperatures over the shutdown threshold. The cooler is clean, the oil is fresh, and there is no obvious hardware fault — because the fault is inside the motor winding material.
How do I know if my compressor has a bad thermal bypass valve?
Signs of a failed-open thermal bypass valve: discharge temperature rises to alarm within 10 to 20 minutes of startup, the cooler is clean and functional, and the machine trips consistently regardless of ambient temperature. Field test: compare oil temperature at cooler inlet versus cooler outlet at operating temperature. If both readings are nearly identical, oil is bypassing the cooler. Thermal bypass valves typically fail after 20,000 to 40,000 hours and are a low-cost replacement part.
Can low oil cause a screw compressor to overheat?
Yes. Lubricating oil absorbs 80 to 90 percent of the heat of compression. Low oil volume reduces the thermal mass available per compression cycle, causing discharge temperatures to rise faster. Degraded oil — even at correct fill level — loses viscosity and thermal capacity, producing similar symptoms. Always check both oil level and oil condition as the first step in any overheating diagnosis.
What is the normal discharge temperature for a screw air compressor?
Normal discharge temperature for an oil-injected rotary screw compressor is 75 to 95 degrees Celsius (167 to 203 degrees Fahrenheit) at 7 to 10 bar working pressure. The thermal bypass valve begins opening at around 70 degrees Celsius and is fully open by 82 to 85 degrees Celsius. Temperatures consistently above 95 degrees Celsius warrant investigation. High-temperature protection shutdown typically activates at 105 to 110 degrees Celsius.
How do copper-clad aluminum motor windings cause compressor overheating?
Copper-clad aluminum windings use wire with a thin copper surface layer over an aluminum core. Aluminum has approximately 60 percent of copper's electrical conductivity, meaning CCA windings generate significantly more heat at identical current load. The stator runs 15 to 25 degrees Celsius hotter than a copper-wound motor. This excess heat transfers into the compressor oil circuit, raising discharge temperatures. On hot summer days, when the cooling system is already operating near capacity, this additional heat source pushes discharge temperatures past the protection threshold. The machine trips. The maintenance team finds no obvious fault. The cycle repeats every summer until the winding insulation fails completely.
Stop the Summer Shutdown Cycle
Ask for the
Motor Certificate.
Every ZIQI compressor ships with a WEG or Wolong motor material certificate confirming 100% copper windings. IE4/IE5 rated. No CCA. No summer trips.
Basic Information
  • Year Established
    --
  • Business Type
    --
  • Country / Region
    --
  • Main Industry
    --
  • Main Products
    --
  • Enterprise Legal Person
    --
  • Total Employees
    --
  • Annual Output Value
    --
  • Export Market
    --
  • Cooperated Customers
    --
Chat
Now

Send your inquiry

Choose a different language
╳
العربية
Беларуская
Deutsch
Ελληνικά
English
Español
français
Magyar
italiano
Nederlands
Português
русский
Current language:English